Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
DECT NR+: How to configure the Physical Layer Control Field Type 2 Header 0

Hey, I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0. According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
38 views

0 replies

Started 3 days ago
by Luca12
Not Answered
Is it possible to get SW support (even non official) for B40 band? 0

We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
35 views

0 replies

Started 3 days ago
by Janne Edgren
Not Answered
BLE advertising power benchmark 0

i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232.... the code runs as expected, though consumes about 200uA when sleeping...
47 views

0 replies

Started 4 days ago
by bios-bob
Not Answered
nRF21540 FEM Not Improving Range in ESB Project (NCS 2.9) 0

We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540. In your Enhanced ShockBurst...
45 views

0 replies

Started 4 days ago
by H. Dekker
Not Answered
nRF9160 SiP - custom board 0

Hi, In my project I am developing a system to monitor the consumption of electricity taken from the grid. The nRF9160 SiP module is responsible for acquiring analogue signals...
- development
- nRF9160
- lte-m
- GPS
- antenna
- hardware
8 views

0 replies

Started 5 days ago
by shak2300

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019