Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Develop Central UART to talk to RedBear Simple Control Arduino board 0

I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...

658 views

0 replies

Started over 9 years ago
by Henry J
Not Answered
Adding a nRF24L01 to a breadboard or stripboard 0

I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
- breadboard
- nrf24l01
1493 views

0 replies

Started over 9 years ago
by Neil Kolban
Not Answered
nRF51822 books, documentation 0

Hello. Can I get a literature to the nRF51 series? I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
- bluetooth low energy
- nrf51822
875 views

0 replies

Started over 9 years ago
by HAKMUN
Not Answered
some connect problem when use hts . 0

hts, HTC phone, nrf tools HTM, nrf51822, every time when it's power up : the once connect: error code 0x7A cann't read characteristic and 0x14 state change. the second...
- hts err manual
703 views

0 replies

Started over 9 years ago
by Liu
Not Answered
4 channel wireless transceiver and 4 RF temperature sensors as a finished product set: 0

Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
- any fcc approved
1061 views

0 replies

Started over 9 years ago
by baha93

Recent in Nordic blog

How We Found a Bug In Nordic’s SDK Using Jumper’s Emulator

dansheme

We were trying to run the PPI example from the nRF5 SDK on our emulator. We quickly revealed a bug in the configuration of one of the timers by having a look at the HW log: Check out our Medium b…
- 24 Aug 2017
New Command Line Interface and enhanced Logger - part 2.

Krzysztof Chruscinski

If you haven't yet get to know command line interface (nrf_cli) module significantly improved in nRF5 SDK 14.0.0 please check this blog post: New command line interface - part 1 Enhanced logger and…
- 22 Aug 2017
MultiLink with Peripherals & Centrals in the nRF5 SDK v13

JustinLee

##Introducing concurrent MultiLinks I’d like to inform that it is possible to configure concurrent-multiple connections with several Centrals and Peripherals. This behavior can be possible to use examples…
- 22 Aug 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020