Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Reviwe for circuit using nRF51822 and Chip ANT 0

Hi All, Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf). I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
867 views

0 replies

Started over 11 years ago
by enojeon
Not Answered

nrf24l01+ how does EN_AA work in detail 0

to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet. then i thought that the settings...

792 views

0 replies

Started over 11 years ago
by thomas
Not Answered
Setting "Custom Data" in nRF51-ble-bcast-mesh 0

I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
- advertising
- s110
- nrf51422
- bluetooth low energy
- mesh
- broadcast
- keil
- nrf51822
1824 views

0 replies

Started over 11 years ago
by Ankit
Not Answered
c99 option and C++ Keil 0

Hello, I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
- c99 cpp libraries keil
2665 views

0 replies

Started over 11 years ago
by Antonio
Not Answered
[Nordic 8001] How to generate a ACI_STATUS_ERROR_PEER_ATT_ERROR from Android? 0

Hello, Is there any way to send an ACI_STATUS_ERROR_PEER_ATT_ERROR from an Android application to the nrf8001 chip? Thanks!
699 views

0 replies

Started over 11 years ago
by Nadgob

Recent in the DevZone Blog

Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018