Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nrf9E5 ADC Calibration 0

We would like to be able to calibrate the rRF9E5 ADC Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
- nrf9e5 adc calibration
655 views

0 replies

Started over 9 years ago
by Damien
Not Answered
breakpoints stopped working with nrf51-dk, gdb and JLinkGDBServer 0

At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger. At...
1404 views

0 replies

Started over 9 years ago
by Clem Taylor
Not Answered
Error: This has file has data in SoftDevice region 0

Hi, I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
- nrf51
- keil
- nrf51822
1572 views

0 replies

Started over 9 years ago
by Sarah
Not Answered
Read String from UART over BLE and execute function? 0

Hello I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
- nrf51-dk
- s110
- bluetooth low energy
- uart
- keil
- nrf51822
2370 views

0 replies

Started over 9 years ago
by kilianod
Not Answered
How to send/Tx IMU sensor Data/Values 0

Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
- nrf24l01+ arduino nano mpu6050
1886 views

0 replies

Started over 9 years ago
by Franks

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020