Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Odd behavior with SOFTDEVICE_HANDLER_INIT w/o Scheduler 0

When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz The project I based...
940 views

0 replies

Started over 10 years ago
by Locky
Not Answered

API to see undiscoverable mode 0

I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...

993 views

0 replies

Started over 10 years ago
by Stavros Tsardounis
Not Answered
How is it possible to make a control flow during burst transfer with nRF24AP2-USB stick ? 0

Please, It seems that "Flow Control" signal is not available on nRF24AP2-USB. EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
- nrf24ap2-usb chip
1263 views

0 replies

Started over 10 years ago
by Flare77
Not Answered
Suggestions for cheapest Arduino basic real-time RFID localization - distance tracking solution? 0

I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
- ble
- arduino
- rfid
- localization
1358 views

0 replies

Started over 10 years ago
by Binyamin
Not Answered
More than 1 UART ? 0

Hi all, I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
- nrf9e5 uart
678 views

0 replies

Started over 10 years ago
by Pascal

Recent in Nordic blog

Log continuously for up to 500 days with the PPK2!

Robin M Saltnes

One of the things you asked us for after launching the new Power Profiler Kit II (PPK2) was extending the maximum logging time, some of you wanted hours or even days of continuous logging. We went to work…
- 19 Feb 2021
Allowing debugger access to nRF5340

Daniel Veilleux

After an nRF5340 executes a power-on, brown-out, watchdog timer, or pin reset it is not automatically accessible to debug probes. This is true even if the nRF5340's memory is completely blank --i.e. no…
- 15 Jan 2021
Connected Home over IP: Sneak peek of early development on nRF52840

Lukasz Duda

This blog post provides step-by-step instruction on running Door Lock example from the CHIP repository. It demonstrates how with help of the mobile phone, commission accessory to the network using Bluetooth…
- 28 Dec 2020

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020