Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Do I need nrfgo to program nrf24lu1 on a custom PCB 0

I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
965 views

0 replies

Started over 10 years ago
by Sean
Not Answered
Can you provide the s120 guid that same as s110(nan-36)? 0

Can you provide the s120 guid that same as s110(nan-36)?
- nrf51822
478 views

0 replies

Started over 10 years ago
by hong tang
Not Answered

Secure DFU/OTA as good as possible to prevent copying my firmware 0

Hi Nordic, I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...

1376 views

0 replies

Started over 10 years ago
by Marius R.
Not Answered
ancs bonding problems 0

After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
- bond ancs
908 views

0 replies

Started over 10 years ago
by makesimply
Not Answered
At first pairing, all pins are working. However, after power on/off and then re-connect the device, only the keyboard key is working. This situation is not always happen. 0

Using nRF51822, I define keys and pins as follows: Keyboard key Mouse left/right key Mouse move (up/down/left/right) Media play/pause key Pin 0 Mouse...
- keyboard
- mouse
- keil
- nrf51822
- media
781 views

0 replies

Started over 10 years ago
by bruce

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020