Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Using irk to get private mac-address 0

Hello We need to scan for more than 8 devices, so we can't use witelist directly. We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
550 views

0 replies

Started over 2 years ago
by Vitaliy
Not Answered
Issues with getting custom board to enter DFU mode for flashing with mcumgr 0

Problem solved :)
552 views

0 replies

Started over 2 years ago
by nRF60D
Not Answered
Zephyr keyboard driver 0

Dear Nordic, Do we have ready-to-use keyboard driver with scanning/debouncing? I've not found an example or docs about using KSCAN with gpio-connected keyboard...
- development
- software
- nrf5 sdk
- zephyr
- nrf52840
486 views

0 replies

Started over 2 years ago
by Dmitry Kr
Not Answered
Ztest of bluetooth 0

Hi, i need to run this ztest for bluetooth , kindly guide me . link - Nordic\v1.9.1\zephyr\tests\bluetooth\bluetooth Regards, Shikamaru
368 views

0 replies

Started over 2 years ago
by Shikamaru
Not Answered
What can cause RTC1_IRQHandler() to throw Mesh error 8 at 0x00000000? 0

Dear Nordic Experts, This one's a tough nut to crack: The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
690 views

0 replies

Started over 2 years ago
by BlueMike

Recent in Nordic blog

nRF BLINKY compatible firmware using Zephyr Bluetooth APIs

vikrant8051

Hello World !! This is simple code which is compatible for nRF Blinky App which is based on Zephyr OS Bluetooth APIs. I've tested it on #nRF52840-PDK board. Isn't it simple ? You have to just replace…
- 24 Jan 2018
How to interface a Nordic Thingy:52 using Amazon Alexa

gamnes

Interfacing the Nordic Thingy:52 from the Amazon Alexa Voice Service just had to be done! In this blog post I will briefly explain how this demo was set up, but I will direct you to the GitHub page if…
- 24 Jan 2018
Difference between nRF52840 Engineering A and B reference designs

MartinBL

After the release of nRF52840 Engineering B we have received several inquiries about the difference between Engineering A (nRF52840-QIAAAA) and Engineering B (nRF52840-QIAABB) reference designs. One reason…
- 15 Jan 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019