Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Is it possible to set the value of the RTC COUNTER in the nRF51822? 0

I see that there is a task for clearing the RTC COUNTER register, but is there a way to initialize the RTC counter value to something other than 0?
- rtc
- keil
- nrf51822
1429 views

0 replies

Started over 11 years ago
by Matt
Not Answered

Battery measurement with ADC on nrf51422, S210 0

I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled. From the example nrf51-ble-app-temp-master, I found...

1381 views

0 replies

Started over 11 years ago
by AndrewM
Not Answered
nRF51822 and windows phone 8.1 0

I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
1734 views

0 replies

Started over 11 years ago
by Mihail
Not Answered
About ble_app_multiactivity_beacon in SDK6.0.0 0

Hello, I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
- ble_app_multiactivity_beacon
601 views

0 replies

Started over 11 years ago
by OPQ
Not Answered

DFU error with iOS 0

Dear Sir We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU. Here is the log data...

964 views

0 replies

Started over 11 years ago
by FU HUNG KWAN

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015