Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not? 0

Hello: I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...

1103 views

0 replies

Started over 10 years ago
by bugg
Not Answered
nRF51822 and nRF24L01+ 0

Hello! How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
- nrf51822 nrf24l01+ addre
799 views

0 replies

Started over 10 years ago
by Schuebbe
Not Answered
uicr related doubts 0

Hi all, i want to know answer related to following question 1)what is use of uicr? 2)if i place some value in uicr and then change the image,then is there will be change...
- bluetooth low energy
- nrf51822
1200 views

0 replies

Started over 10 years ago
by renu
Not Answered
Master Control Panel doesn't work (python error). 0

It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file: 0;13:45:18.9900 [MainThread...
- master control panel
974 views

0 replies

Started over 10 years ago
by Tim
Not Answered

how to change the type of event executing? 0

Hi all! My question is: My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...

581 views

0 replies

Started over 10 years ago
by kk

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020