Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

To implement iBeacon what are the things to be take care at the peripheral side. 0

Hi Team, To implement iBeacon what are the things to be take care at the peripheral side. Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...

994 views

0 replies

Started over 10 years ago
by Ibrahim
Not Answered
PCA10001 hex file for proximity app 0

Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
- nrf51822 proximity
804 views

0 replies

Started over 10 years ago
by Fred Roeber
Not Answered

Timeslot API - modify a radio request 0

Hi, What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session? For example,...

1046 views

0 replies

Started over 10 years ago
by Gili Elias
Not Answered
sd_ant_channel_id_set returns NRF_ERROR_INVALID_ADDR 0

Hi, I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
- nrf51422
- ant
864 views

0 replies

Started over 10 years ago
by Paul Damade
Not Answered
ANT Extended Messaging in API 0

Hi, To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
- nrf51422
- ant
- scan
817 views

0 replies

Started over 10 years ago
by Us

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022