Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Can't connect directly after I exit our app by back key on phone
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi, My behavior is as follows Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic) Turn on my cell phone(Samsung Note3),scan my device...

499 views

0 replies

Started over 10 years ago
by Elliot.Chao
Not Answered

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hello: I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...

1104 views

0 replies

Started over 10 years ago
by bugg
Not Answered
nRF51822 and nRF24L01+
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hello! How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
- nrf51822 nrf24l01+ addre
800 views

0 replies

Started over 10 years ago
by Schuebbe
Not Answered
uicr related doubts
View Voters Login to vote on this thread +1 Login to vote on this thread
0

Hi all, i want to know answer related to following question 1)what is use of uicr? 2)if i place some value in uicr and then change the image,then is there will be change...
- bluetooth low energy
- nrf51822
1200 views

0 replies

Started over 10 years ago
by renu
Not Answered
Master Control Panel doesn't work (python error).
View Voters Login to vote on this thread 0 Login to vote on this thread
0

It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file: 0;13:45:18.9900 [MainThread...
- master control panel
975 views

0 replies

Started over 10 years ago
by Tim

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020

Nordic DevZone

Can't connect directly after I exit our app by back key on phone View Voters Login to vote on this thread 0 Login to vote on this thread 0

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not? View Voters Login to vote on this thread 0 Login to vote on this thread 0

nRF51822 and nRF24L01+ View Voters Login to vote on this thread 0 Login to vote on this thread 0

uicr related doubts View Voters Login to vote on this thread +1 Login to vote on this thread 0

Master Control Panel doesn't work (python error). View Voters Login to vote on this thread 0 Login to vote on this thread 0

Can't connect directly after I exit our app by back key on phone
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

nRF51822 and nRF24L01+
View Voters Login to vote on this thread 0 Login to vote on this thread
0

uicr related doubts
View Voters Login to vote on this thread +1 Login to vote on this thread
0

Master Control Panel doesn't work (python error).
View Voters Login to vote on this thread 0 Login to vote on this thread
0