Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
HID Service on iOS 0

I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
1963 views

0 replies

Started over 10 years ago
by Adam
Not Answered

the speed of large amount of data 0

int main(void) { uint32_t BufferCount; uint32_t err_code; // Initialize leds_init(); timers_init(); buttons_init(); uart_init(); ble_stack_init(); gap_params_init...

950 views

0 replies

Started over 10 years ago
by fitfuel
Not Answered
Gazell library source code. 0

Hi I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
- gazell
- nrf51822
1502 views

0 replies

Started over 10 years ago
by Firek
Not Answered

PWM / Timer question 0

HI, I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...

3069 views

0 replies

Started over 10 years ago
by Jacques
Not Answered

what's the function of the paramter BLE_L2CAP_MTU_DEF? 0

hello, the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight. ble_app_uart :...

2282 views

0 replies

Started over 10 years ago
by dangerous_man

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020