Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

after flash DFU, com3 is not accessable 0

after flash DFU program into pca10001 board, com3 is not accessible, www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png even after I erase all, and re upload soft...

698 views

0 replies

Started over 11 years ago
by julian
Not Answered
Subsequent sd_ble_gattc_read does not return 0

Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP, received 0x16 bytes of data but there is more to read. Next call to sd_ble_gattc_read using the same connection...
- s120
- receive
- bluetooth low energy
- softdevice
- gatt
1554 views

0 replies

Started over 11 years ago
by Mark Mendelsohn
Not Answered

Why Bluetooth Go to system-off mode, sramon can not be stored. 0

Hello： Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...

1378 views

0 replies

Started over 11 years ago
by bugg
Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

654 views

0 replies

Started over 11 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

836 views

0 replies

Started over 11 years ago
by kazuo KATO

Recent in Nordic blog

Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017