Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

809 views

0 replies

Started over 12 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

998 views

0 replies

Started over 12 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1533 views

0 replies

Started over 12 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1474 views

0 replies

Started over 12 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
1126 views

0 replies

Started over 12 years ago
by Pedro Lopes

Recent in the DevZone Blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017
OLED display support for nRF52832 (SSD1306, Adafruit GFX)

Mahesh Venkitachalam

Just a quick post to say that we have ported the Adafruit GFX and SSD1306 libraries to nRF52832. Currently only I2C is supported. The code can be found here: https://github.com/electronut/ElectronutLabs…
- 11 Aug 2017
I tried 5 different debugger IDEs for nRF52 and STM32. Here are my results.

Jonathan

At Jumper we’re developing tools that increase the happiness levels of embedded software developers. Our main tool to date is the Jumper Emulator. As a part of the development process we’re required to…
- 9 Aug 2017
Things you should know about Bluetooth mesh

Eirik Midttun

Bluetooth SIG has recently published a new standard, the Bluetooth mesh. The mesh capability is a significant update and enables radical new applications. This in turn means that there are significant…
- 7 Aug 2017