Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE USB powered OEM dongle with nRF51822 0

We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software. It would need to come complete with casing and the ability...
- usb dongle ble nrf51822
734 views

0 replies

Started over 10 years ago
by Chris
Not Answered
related to threads 0

Hi all, i want to establish connection between two threads in cmsis-rtos, can i use 1) semaphore to do this? 2)message queue should be used or any other ipcs can be...
895 views

0 replies

Started over 10 years ago
by renu
Not Answered

Data transfer rate by serialization 0

Hi, I have two CPU in our product. (STM32F2 and Nordic nrf51422). I use serialization function to link those two CPU(refer to ble_s110_serialization sample) But I find...

711 views

0 replies

Started over 10 years ago
by Elliot.Chao
Not Answered

Can't connect directly after I exit our app by back key on phone 0

Hi, My behavior is as follows Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic) Turn on my cell phone(Samsung Note3),scan my device...

504 views

0 replies

Started over 10 years ago
by Elliot.Chao
Not Answered

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not? 0

Hello: I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...

1110 views

0 replies

Started over 10 years ago
by bugg

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020