Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

611 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

795 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1304 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1257 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
885 views

0 replies

Started over 10 years ago
by Pedro Lopes

Recent in Nordic blog

Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019