Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

810 views

0 replies

Started over 11 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1322 views

0 replies

Started over 11 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1280 views

0 replies

Started over 11 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
902 views

0 replies

Started over 11 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1044 views

0 replies

Started over 11 years ago
by julian

Recent in Nordic blog

Developing for the nRF52820 with nRF5 SDK v16.0.0

bjorn-spockeli

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020
How we build ThingyWorld for embedded world 2020

Markus Tacker (he/him)

In this post we describe how we build the ThingyWorld demo for embedded world 2020.
- 2 Mar 2020
On nRF Connect for iOS & SIMD Optimizations in Swift

Dinesh Harjani

We released a small update late last week. It’s a follow-up to our last release of 2019, and like its predecessor, this release, 2.1.2, aims to improve the general stability of nRF Connect for iOS as well…
- 31 Jan 2020
Q&A for "Embedded Antennas for IoT" webinar

Petter Myhre

This blog post contains answers to questions asked during the "Embedded Antennas for IoT" webinar hosted by Nordic Semiconductor 17.10.2019. You can watch a recording of the webinar here. You…
- 22 Nov 2019
nRF Connect 2.1 for iOS: Welcoming Dark Mode

Dinesh Harjani

It has taken a lot longer than we previously thought, but we made it here, to our first big point release for nRF Connect 2.0. Throughout this “two-point-oh" journey, you’ve been an invaluable asset to…
- 19 Nov 2019
nRF5 SDK v 16.0 : Flashing nRF52833 in Keil uVision

Susheel Nuguru

This page describes an easy workaround for the flashing error you get in Keil uVision when you are using nRF5 SDK v16 on nRF52833 chips. The assumption is that you have installed the latest versions of…
- 18 Oct 2019