Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

To implement iBeacon what are the things to be take care at the peripheral side. 0

Hi Team, To implement iBeacon what are the things to be take care at the peripheral side. Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...

1001 views

0 replies

Started over 10 years ago
by Ibrahim
Not Answered
PCA10001 hex file for proximity app 0

Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
- nrf51822 proximity
809 views

0 replies

Started over 10 years ago
by Fred Roeber
Not Answered

Timeslot API - modify a radio request 0

Hi, What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session? For example,...

1052 views

0 replies

Started over 10 years ago
by Gili Elias
Not Answered
sd_ant_channel_id_set returns NRF_ERROR_INVALID_ADDR 0

Hi, I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
- nrf51422
- ant
870 views

0 replies

Started over 10 years ago
by Paul Damade
Not Answered
ANT Extended Messaging in API 0

Hi, To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
- nrf51422
- ant
- scan
822 views

0 replies

Started over 10 years ago
by Us

Recent in Nordic blog

ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017
OLED display support for nRF52832 (SSD1306, Adafruit GFX)

Mahesh Venkitachalam

Just a quick post to say that we have ported the Adafruit GFX and SSD1306 libraries to nRF52832. Currently only I2C is supported. The code can be found here: https://github.com/electronut/ElectronutLabs…
- 11 Aug 2017
I tried 5 different debugger IDEs for nRF52 and STM32. Here are my results.

Jonathan

At Jumper we’re developing tools that increase the happiness levels of embedded software developers. Our main tool to date is the Jumper Emulator. As a part of the development process we’re required to…
- 9 Aug 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019