Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

619 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

802 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1311 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1266 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
893 views

0 replies

Started over 10 years ago
by Pedro Lopes

Recent in Nordic blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020