Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Regarding ble mesh data transfer 0

Hi, Kit:nrf5340 Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts. Is ble controller will be enabled during...
486 views

0 replies

Started over 3 years ago
by Priyadharshini
Not Answered
Modem firmware python script file or dependency missing 0

I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
528 views

0 replies

Started over 3 years ago
by okwestern
Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
659 views

0 replies

Started over 3 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
500 views

0 replies

Started over 3 years ago
by meghna
Not Answered

Please close this thread 0

Please close this thread

483 views

0 replies

Started over 3 years ago
by kerimkilic

Recent in Nordic blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019