Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Use keypad for wakeup (kbd_matrix) from deep sleep (sys_poweroff) 0

I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
11 views

0 replies

Started 1 hour ago
by Crox
Not Answered
Writing to flash memory 0

Hi, I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex. I want to write some information (just 4 bytes) to flash memory,...
- development
- software
- flash
- nrf52810
11 views

0 replies

Started 1 hour ago
by Kenneth_CBS
Not Answered
Unable to configure nRF Sniffer for 802.15.4 for ZigBee 0

Hello All, I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup, https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
8 views

0 replies

Started 1 hour ago
by UVP
Not Answered
Can't open syscall/gpio.h 0

Hi everyone, I am getting this build error while I am trying to call a function from gpio.h in my custom code Looking at my includes I see this This is a really...
12 views

0 replies

Started 1 hour ago
by ReginaA101
Not Answered
Timeout exit from the boot loader 0

I am developing an application that uses NCS2.8.0. For FW updates, the nRF52833 USB ACM bootloader is enabled. However, there are some problem. My device has a battery...
10 views

0 replies

Started 2 hours ago
by DX_HK

Recent in Nordic blog

IoT Contest - Mini-Weather Station - Project

buleks

The role of this device is remote measurement environment parameters. It could be accessed anywhere where access to the internet is possible. It uses 6LoWPAN because it's modern IoT technology and have…
- 9 Jul 2015
External nRF51822 SWD Programming using the nRF51-DK

Mahesh Venkitachalam

I've written up a note on programming external nRF51822 boards (like the RedBearLab Nano) using the SWD interface of the nRF51-DK. http://electronut.in/nrf51-dk-external-programming/
- 9 Jul 2015
Getting started with nRF51822 and GCC - transmitting LDR light levels over BLE

Mahesh Venkitachalam

I've written up a simple project that uses the nRF51-DK to send LDR light levels over BLE using the Nordic UART Service (NUS). In the process, I have set up a cross-platform toolchain (OS X, Windows) using…
- 8 Jul 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019