Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Using RTC0 with nrf9151 custom board 0

Hi all, I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file In my prj.conf But...
17 views

0 replies

Started 2 hours ago
by simon884
Not Answered
Reg: Zephyr OpenThread Joiner crashes after Join success — Kernel oops 0

We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
24 views

0 replies

Started 4 hours ago
by Lavanya_Manohar
Not Answered
nrf9160 0

I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect. The lte_lc_connect_async...
16 views

0 replies

Started 5 hours ago
by amelio
Not Answered
reducing current consumption of nrf54l15 GPIO interrupts configured for edge triggering 0

In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
- development
- software
- nRF54L15
- zephyr
- low-power
24 views

0 replies

Started 6 hours ago
by zming
Not Answered
nRF54L15 watch crystal load capacity tuning 0

Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
31 views

0 replies

Started 7 hours ago
by Gardening Stevie

Recent in Nordic blog

Writing BLE firmware with a few lines of code part 2

Nguyen Hoan Hoang

Second part of the series Writing Bluetooth LE firmware the easy way blog. This second part shows how to read and advertise the environment sensor data (BME280 using Motsai Neblina module and BME680 using…
- 3 Jan 2018
Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017