Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 unable to enter MCUboot serial recovery mode via UART 0

I am trying to enter MCUboot serial recovery mode on an nRF5340 through a UART command. I mainly followed the Nordic tutorial below: https://academy.nordicsemi.com/courses...
19 views

0 replies

Started 8 hours ago
by Ki0
Not Answered
DFU fails after NCS SDK update from v3.2.4 to v3.3.0 on custom nRF54L15 board with compressed images 0

We are using a custom board based on nRF54L15 with MCUboot and compressed image DFU over OTA. DFU was working correctly when updating between NCS v3.2.0 and v3.2.4, but after...
30 views

0 replies

Started 10 hours ago
by Aasim_
Not Answered
Mesh OTA couldn't resume after target node reset 0

Hi， I use NCS 3.2.4 and 54L15 DK. In the DFU target, I added configuration and also added the following content in dfu_recover function. After the distributor...
- software
- nRF54L15
- mesh
- nrf52840
- Pre-production
33 views

0 replies

Started 11 hours ago
by John
Not Answered
nrf52840 ncs-v3.0.2 Power consumption 450μA 0

Hello, I am developing a low-power nRF52840 product using the ncs Zephyr environment. Currently, I have suspended peripherals such as UART and I2C, allowing the system to...
53 views

0 replies

Started 12 hours ago
by njghzht
Not Answered
nRF54LM20A: APPROTECT/SECUREAPPROTECT in UICR not taking effect after reset 0

Hi everyone, I am currently facing an issue with the nRF54LM20A where the access port protection is not taking effect after programming SECUREAPPROTECT and APPROTECT into...
50 views

0 replies

Started 14 hours ago
by wenc

Recent in the DevZone Blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018
Introducing experimental release of Programmer Application

Reidar Martin Svendsen

nRF Connect for desktop has proven its flexibility by being cross platform and ability to install and update applications based on users need. Motivation Our initial goal was to modernize and cover…
- 30 Apr 2018
New in nRF5 SDK v15: Strong Hardware-Based Security with Infineon OPTIGA Trust X

ChristianLesjak

Defining a business model and implementing a technical infrastructure are two major phases in building a successful product or IoT system. However, protecting the business model and your customer’s data…
- 9 Apr 2018