Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Matter firmware can not run in custom board(nrf54l15) 0

I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
26 views

0 replies

Started 7 hours ago
by jared_jia
Not Answered
unknow data when use qspi panel 0

Hi all, I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem. The red area is the data I sent, but the blue area is not what I sent....
14 views

0 replies

Started 7 hours ago
by Wayne_Chang
Not Answered
How to use nrf54L15-dk with external host through hci uart application 0

Hi, I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
15 views

0 replies

Started 8 hours ago
by Abhinav152
Not Answered
Pin assignment for UART on the nRF54L15DK 0

Hello. I am testing UART connectivity using the nRF54L15DK. After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
15 views

0 replies

Started 9 hours ago
by a.da
Not Answered
Some problems about Periodic advertising 0

The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
13 views

0 replies

Started 11 hours ago
by Caesarzhou

Recent in Nordic blog

Field-testing how distance affects the behavior of LTE-M and NB-IoT

Petter Myhre

There is an updated field test at the same location from 2022. During the updated field test, we captured more parameters for both LTE-M and NB-IoT devices and, we captured power measurements of the cellular…
- 2 May 2019
SEGGER Embedded Studio Nordic edition updates v4.16

Hung Bui

Recently, we've updated the SEGGER Embedded Studio Nordic edition (SES) to version 4.16 (SES Nordic Edition is special version of SES built specifically for nRF Connect SDK). This updated version introduced…
- 12 Apr 2019
nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020