Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
mesh dfu distributor image size 0

Hello I am playing with the mesh dfu and the distributor application on nRF52840 DK board I load the image I want to distribute using mcumgr application on a Raspberry...
19 views

0 replies

Started 5 hours ago
by AndyM
Not Answered
Nrf9160 boost converter 0

Hi, Im designing a custom board using a NRF9160 MCU. From the product specification it operates at a voltage range of 3.0(2.8)-5.5V. I want to use a 3xLI socl2 3.6v (parallel...
20 views

0 replies

Started 6 hours ago
by Miguel Ferreira
Not Answered
Notification count in BLE_GATTS_EVT_HVN_TX_COMPLETE event is greater than expected 0

Hello, We are facing an issue where the sum of count in BLE_GATTS_EVT_HVN_TX_COMPLETE events (member of the ble_gatts_evt_hvn_tx_complete_t structure) doesn't match with...
- software
- nrf5 sdk
- softdevice
- bluetooth le
- nrf52840
- s140
- production
29 views

0 replies

Started 6 hours ago
by Joaliasbarb
Not Answered
nRF Connect VScode project issue with GPIO configuration 0

Hi, I created a simple project in VS Code and I have defined the custom board configuration files that I want. In the xxx_defconfig file I have defined CONFIG_GPIO=y but...
18 views

0 replies

Started 7 hours ago
by masterLee
Not Answered
CONFIG_NRFX_TIMER1 was assigned the value y, but got the value n. Missing dependencies: HAS_NRFX || (HAS_NRFX && 0) || ((UART_0_NRF_HW_ASYNC_TIMER = 1 || UART_1_NRF_HW_ASYNC_TIMER = 1 || UART_2_NRF_HW_ASYNC_TIMER = 1 || UART_3_NRF_HW_ASYNC_TIME 0

Im using nrf5340 with nrf connect SDK 2.6. Im trying to follow this post to evaluate hardware timer for reading saadc But I constantly am getting CONFIG_NRFX_TIMER1...
19 views

0 replies

Started 7 hours ago
by IvanR

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019