Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Zephyr Input and GPIO P2 configuration issues on nRF54H20-DK v0.8.2 0

Hi. Currently evaluating this DK. I'm using project that is based on samples\subsys\usb\hid-keyboard example from SDK v2.8.0-rc2. I have added more input pins via Zephyr...
15 views

0 replies

Started 3 hours ago
by Kyrylo
Not Answered
Failed to perform SPI read function on nRF52840dk with BMI270 sensor 0

Hello, I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
- software
- Evaluation
- spi
- nrf52840
19 views

0 replies

Started 3 hours ago
by Shuhao Dong
Not Answered
Failed to clone the repositories when trying to install SDK 2.7.0 0

Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error: Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
22 views

0 replies

Started 5 hours ago
by SOOK
Not Answered
Cracen drivers preventing some ciphers from being compiled in 0

Hello, I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
39 views

0 replies

Started 6 hours ago
by alexdr5398
Not Answered
Size of build image for mcuboot with serial or usb DFU enabled? 0

Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader. I had a mucboot setup that fitted...
16 views

0 replies

Started 7 hours ago
by BrianW

Recent in Nordic blog

Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019