Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Isochronous channel for sensor data streaming 0

Hi, I am working on a project that collects data from various sensors and transmits it to a Mobile application via BLE. Can I use Isochronous Streaming for it? Can I set up...
11 views

0 replies

Started 3 hours ago
by pal_722
Not Answered
NDT outside of Zephyr (specifically arduino) 0

Hi, My ultimate goal is to add NDT [1] to a meshtastic [2] device implemented with RAK4631[3]. For this goal I can see the following obstacles: - The meshtastic stack...
- software
- Evaluation
- softdevice
- zephyr
- bluetooth le
- nrf52840
- Architecture
29 views

0 replies

Started 11 hours ago
by jbozzo
Not Answered
Executing Shell commands from Mcumgr 0

nRF Connect SDK 2.6.1 + nRF52832 I can't get the execution of shell commands from mcumgr over SMP to work. Here is my prj.conf : I registered some custom shell commands...
27 views

0 replies

Started 14 hours ago
by MartinZ
Not Answered
NCS - Devicetree & nrfx coexistence 0

Hi, I have an application based on the "peripheral_uart" sample code (nRF52840DK, NCS2.70) As I use interchangeably the same pins as GPIOs and UARTE1, I use UARTE1 with...
31 views

0 replies

Started 15 hours ago
by eyalasko
Not Answered
Bluetooth: HCI low power UART working as peripheral and central at the same time 0

Dear Nordic, We wonder if it is possible to connect to the BLE side of nRf9160dk using the LTE BLE Gateway sample. https://docs.nordicsemi.com/bundle/ncs-2.3.0/page/nrf/samples...
29 views

0 replies

Started 15 hours ago
by mjaszczykowski

Recent in Nordic blog

Smart Remote 3 for nRF52

John Leonard

Smart Remote 3 for nRF52 setting a new standard for voice input features and ultra-low power performance in smart remote controls Nordic Semiconductor has recently released the latest member of their…
- 7 Sep 2016
Getting started with nRF5 and CadSoft EAGLE (R)

Øystein Smith

Nordic Semiconductor already provides reference designs for Altium Designer (R), but if you prefer EAGLE here is a quick guide on how to use the EAGLE reference design. This quick guide assumes you are…
- 6 Sep 2016
Profiling the Softdevice and FreeRTOS with Segger SystemView

Tim

In a previous blog post, RK has shown us how to use Segger SystemView to monitor a bare-metal application as well as the Softdevice. Based on his work, we will see how to go further and add FreeRTOS to…
- 3 Sep 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019