Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to use http_client or https_client to send a post message to my web server? 0

Hello! I threw away the Sparkfun board and replaced it with a nRF9151DK board; I'm hoping to get it work now, after trying for a year. I'm using SDK 2.6.1 and 2.8.0; the...
22 views

0 replies

Started 16 hours ago
by Digisoles
Not Answered
matter light switch 0

example Matter_light_switch in vs code version using nrf connect sdk -> v2.8.0 manage tool-chain version v2.8.0 nrf52840dk getting error while building code ...
16 views

0 replies

Started 18 hours ago
by Prajwal Tayade
Not Answered
DECT NR+ power class and bandwidth/data rate 0

Hello, I have a few questions about the nRF9151 DECT NR+ modem. I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
18 views

0 replies

Started 18 hours ago
by Mark Szente
Not Answered
how to obtain a fixed BLE MAC address when CONFIG_BT_PRIVACY is defined 0

Hi, I am using nrf52840 to develop a product. I use NCS sdk v2.5.0. I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
24 views

0 replies

Started 1 day ago
by zhuweihua163
Not Answered
Setting CONFIG_BT_CTLR_DATA_LENGTH_MAX=251 but payload is limited to 229 bytes. 0

We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version. We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
27 views

0 replies

Started 1 day ago
by Mike.Redd

Recent in Nordic blog

Building a BLE application step by step from scratch

Jocelyn Masserot

Hi all, I'm working on a blog explaining from scratch how to develop a BLE application with nRF518122 chip. Step by step, I explain the different aspects of the embedded system development in a GCC environment…
- 11 Feb 2016
Segger Embedded Studio blog post rev2 DEPRECATED

Michael Dietz

Depreceted see new blog post for new version of embedded studio here: https://devzone.nordicsemi.com/blogs/1032/segger-embedded-studio-a-cross-platform-ide-w-no-c/ #Introduction This post is an introductory…
- 4 Feb 2016
BLE-to-SB quadcopter bridge

Daniel Veilleux

[UPDATE (Feb 8, 2016): I have incorporated the feedback that I received from several link-layer wizards in Trondheim.] Last fall I purchased an inexpensive quadcopter that uses Nordic's ShockBurst (SB…
- 4 Feb 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019