Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Deleted 0

Deleted

401 views

0 replies

Started over 4 years ago
by liammcnair
Not Answered
nRF9160 LTE and GPS matching network 0

Hi , I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
700 views

0 replies

Started over 4 years ago
by Netanel
Not Answered
When porting Arduino i2c sensor driver to nrf52... 0

I am a student interested in Nordic. My coding skills are very poor. So I want to get help. I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
795 views

0 replies

Started over 4 years ago
by eggmoneyna
Not Answered
low level interrupt not firing after porting from SDK 15.3 to SDK 17.0.2 0

I have a working project where pin 16 is configured as a low-level interrupt source. it is working well with SDK 15.3 after porting to SDK 17.0.2, it is not triggering...
407 views

0 replies

Started over 4 years ago
by kobyfr
Not Answered
Thank you 0

Hello Nordic Support Engineers and fellow developers ... Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
551 views

0 replies

Started over 4 years ago
by Tim

Recent in Nordic blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019