Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
atomic fifo implementation on armv7a 0

Hi Nordic Team, The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
- development
- software
- nrf5 sdk
- arm
514 views

0 replies

Started over 3 years ago
by misaka
Not Answered
Regarding ble mesh data transfer 0

Hi, Kit:nrf5340 Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts. Is ble controller will be enabled during...
486 views

0 replies

Started over 3 years ago
by Priyadharshini
Not Answered
Modem firmware python script file or dependency missing 0

I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
528 views

0 replies

Started over 3 years ago
by okwestern
Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
659 views

0 replies

Started over 3 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
500 views

0 replies

Started over 3 years ago
by meghna

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019
Getting started: How to get modem trace using “Trace Collector” in nRF Connect

Brian Kim

UPDATE MAY 2021:Please follow the official documentation in infocenter. The following information is deprecated, please follow the documentation link at the top. Trace Collector app collects UART traces…
- 30 Apr 2019
Getting started: Store dust sensor data on nRF Connect for Cloud

Markus Tacker (he/him)

In this example we are using the nRF Connect for Cloud Device API, which is a free service for protyping IoT products and is built on top of AWS IoT, to store dust sensor readings. The API is device-agnostic…
- 12 Mar 2019
Mesh Networks: Provisioning and running Nordic's BLE Mesh with Python Application Controller Interface (PyACI)

Mark Q

Purpose This document will explain the Mesh Demo and the motivations behind the design decisions. Please find attached PDF file at the bottom of this tutorial for high-resolution version of this tutorial…
- 3 Feb 2019
Getting Started : Using GDB with Nordic devices

Daniel Veilleux

The GNU Debugger (GDB) is a popular tool that provides familiar features like breakpoints along with a command syntax that allows creativity in the debugging process. Although its command line interface…
- 31 Jan 2019
Getting started: Getting Started with nRF9160 DK

Akash Patel

2020-08-04: The content of this guide is now covered in the documentation on Infocenter. For the most up-to-date Getting started guide with nRF9160 DK please follow this link. 2020-03-09: Updated tutorial to…
- 2 Jan 2019