Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF9160 LTE and GPS matching network 0

Hi , I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
641 views

0 replies

Started over 3 years ago
by Netanel
Not Answered
When porting Arduino i2c sensor driver to nrf52... 0

I am a student interested in Nordic. My coding skills are very poor. So I want to get help. I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
747 views

0 replies

Started over 3 years ago
by eggmoneyna
Not Answered
low level interrupt not firing after porting from SDK 15.3 to SDK 17.0.2 0

I have a working project where pin 16 is configured as a low-level interrupt source. it is working well with SDK 15.3 after porting to SDK 17.0.2, it is not triggering...
376 views

0 replies

Started over 3 years ago
by kobyfr
Not Answered
Thank you 0

Hello Nordic Support Engineers and fellow developers ... Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
511 views

0 replies

Started over 4 years ago
by Tim
Not Answered
Website links/downloads for Thingy91 removed? 0

Hi, I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
328 views

0 replies

Started over 4 years ago
by justinm_nz

Recent in Nordic blog

Field-testing how distance affects the behavior of LTE-M and NB-IoT

Petter Myhre

There is an updated field test at the same location from 2022. During the updated field test, we captured more parameters for both LTE-M and NB-IoT devices and, we captured power measurements of the cellular…
- 2 May 2019
SEGGER Embedded Studio Nordic edition updates v4.16

Hung Bui

Recently, we've updated the SEGGER Embedded Studio Nordic edition (SES) to version 4.16 (SES Nordic Edition is special version of SES built specifically for nRF Connect SDK). This updated version introduced…
- 12 Apr 2019
nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019