Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Zephyr keyboard driver 0

Dear Nordic, Do we have ready-to-use keyboard driver with scanning/debouncing? I've not found an example or docs about using KSCAN with gpio-connected keyboard...
- development
- software
- nrf5 sdk
- zephyr
- nrf52840
549 views

0 replies

Started over 2 years ago
by Dmitry Kr
Not Answered
Ztest of bluetooth 0

Hi, i need to run this ztest for bluetooth , kindly guide me . link - Nordic\v1.9.1\zephyr\tests\bluetooth\bluetooth Regards, Shikamaru
449 views

0 replies

Started over 2 years ago
by Shikamaru
Not Answered
What can cause RTC1_IRQHandler() to throw Mesh error 8 at 0x00000000? 0

Dear Nordic Experts, This one's a tough nut to crack: The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
772 views

0 replies

Started over 3 years ago
by BlueMike
Not Answered
CMAC calculation failed with SDK 1.9.1 0

SoC: nRF5340 SDK: nRF Connect SDK 1.9.1 CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1. psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
527 views

0 replies

Started over 3 years ago
by Dan2022
Not Answered
Slides from the Electromaker contest Q&A webinar 0
381 views

0 replies

Started over 3 years ago
by Robin M Saltnes

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020