Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Publish timeout handler of a model called during opcode handling of a message in the same model (or vice versa) 0

Hi, This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
361 views

0 replies

Started over 4 years ago
by Mathias
Not Answered
New nRF52840 finger tip size module with Type-C Dongle fully compatible with Nordic dongle 0

Hi to all Nordic product lovers, This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
1217 views

0 replies

Started over 4 years ago
by Nguyen Hoan Hoang
Not Answered
Bitwise operations on uint8_t / Integer promotion 0

Hi, I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
1021 views

0 replies

Started over 4 years ago
by fuesel
Not Answered
CMSIS tool 0

Hello, Is there a way to show only enabled options in CMSIS tool? If not, that would be a nice enhancement for future versions. Thanks, Sam
825 views

0 replies

Started over 4 years ago
by Sam123
Not Answered
Erase 0

I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
402 views

0 replies

Started over 4 years ago
by Malcolm

Recent in Nordic blog

Logging enabled by default in SDK Bluetooth examples

Håvard

Several users have pointed out a sudden flash size increase in some of our Bluetooth examples. We decided to write a quick post here to describe the reason for this and explain how to decrease the size…
- 29 Mar 2017
Monitor Mode Debugging with J-Link and GDB/Eclipse

Daniel Veilleux

The biggest pain point when debugging an application on the nRF51 series is the inability to set breakpoints while the SoftDevice is active without triggering an assert. Although a workaround exists that…
- 29 Mar 2017
Throughput and long range demo

ovrebekk

The new Bluetooth 5 specification promises twice the speed and 4 times the range. Doubling the speed is achieved by increasing the on-air datarate to 2Mbps, while quadrupling the range is achieved by lowering…
- 28 Feb 2017

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020