Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Publish timeout handler of a model called during opcode handling of a message in the same model (or vice versa) 0

Hi, This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
361 views

0 replies

Started over 4 years ago
by Mathias
Not Answered
New nRF52840 finger tip size module with Type-C Dongle fully compatible with Nordic dongle 0

Hi to all Nordic product lovers, This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
1217 views

0 replies

Started over 4 years ago
by Nguyen Hoan Hoang
Not Answered
Bitwise operations on uint8_t / Integer promotion 0

Hi, I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
1021 views

0 replies

Started over 4 years ago
by fuesel
Not Answered
CMSIS tool 0

Hello, Is there a way to show only enabled options in CMSIS tool? If not, that would be a nice enhancement for future versions. Thanks, Sam
825 views

0 replies

Started over 4 years ago
by Sam123
Not Answered
Erase 0

I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
402 views

0 replies

Started over 4 years ago
by Malcolm

Recent in Nordic blog

Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017

Latest guides

Peripherals And RF Test: Writing device drivers for UART peripherals

Halvor Bjorstad

This post aims to cover some of the specifics of developing device drivers for UART peripherals for Zephyr.
- 20 Jul 2021
Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021