Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
External NAND flash with nRF5340 (non-SPI) 0

I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
- flash
- hardware
- Pre-production
- nRF5340
1439 views

0 replies

Started over 4 years ago
by mattgaidica
Not Answered
RAM START ADDRESS 0

Hi I try to run BLE HRS collector example. when I run the project, in RTT terminal I have these error 00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
- s130
- software
- Evaluation
- nrf51
- nrf51802
896 views

0 replies

Started over 4 years ago
by M.A.N.
Not Answered
Google: Say hello to OpenSK: a fully open-source security key implementation using nRF52840 Dongle (among others) 0

Google open-sources the firmware needed to build hardware security keys Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
2676 views

0 replies

Started over 4 years ago
by LarsH
Not Answered
Mesh 4.0 SDK Flash Manager - Storing values 0

I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
- development
- software
- flash
- mesh
- nRF Mesh
- nrf52832
779 views

0 replies

Started over 4 years ago
by joao
Not Answered
Python bindings on openwrt? 0

Hello, Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
541 views

0 replies

Started over 4 years ago
by pcav99

Recent in Nordic blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019