Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF9161 SIM LTE connectivity issue 0

Hello, We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
13 views

0 replies

Started 3 hours ago
by sposelenov
Not Answered
handle nrf_libuarte_async_evt_t in thread mode 0

Hello, I'm using nRF5 SDK v17.1.0. I couldn't find anything about it. Could I ran in some problems if i choose to handle the nrf_libuarte_async_evt_t in thread mode and...
20 views

0 replies

Started 3 hours ago
by jul-nc
Not Answered
Build for custom board converted to 2.8 format getting error "list GET given empty list" in CMakeLists.txt splitting BOARD_QUALIFIERS 0

We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
15 views

0 replies

Started 3 hours ago
by robbsadler
Not Answered
Weak Pin Drive Strength on nRF5340 DK Leading to SPI Communication Failure with ICM-42688-P 0

I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
- nRF Connect SDK
- Evaluation
- spi
- hardware
- nRF5340
19 views

0 replies

Started 4 hours ago
by MatryoshkaLJY
Not Answered
PPK2-PowerSwitch SW1 0

Hello, I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
16 views

0 replies

Started 4 hours ago
by HBehr

Recent in Nordic blog

IoT Contest - Mini-Weather Station - Project

buleks

The role of this device is remote measurement environment parameters. It could be accessed anywhere where access to the internet is possible. It uses 6LoWPAN because it's modern IoT technology and have…
- 9 Jul 2015
External nRF51822 SWD Programming using the nRF51-DK

Mahesh Venkitachalam

I've written up a note on programming external nRF51822 boards (like the RedBearLab Nano) using the SWD interface of the nRF51-DK. http://electronut.in/nrf51-dk-external-programming/
- 9 Jul 2015
Getting started with nRF51822 and GCC - transmitting LDR light levels over BLE

Mahesh Venkitachalam

I've written up a simple project that uses the nRF51-DK to send LDR light levels over BLE using the Nordic UART Service (NUS). In the process, I have set up a cross-platform toolchain (OS X, Windows) using…
- 8 Jul 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019