Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 LFCLK sources control 0

Hi, I would like to ask when using zephyr's k_timer it uses a clock from LFCLK, then it can be generated in the following three ways: 32.768 kHz RC oscillator (LFRC) 32...
22 views

0 replies

Started 6 hours ago
by Zion
Not Answered
When connecting to AWS IoT with low signal it gets stuck 0

We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
21 views

0 replies

Started 6 hours ago
by charleshaf
Not Answered
With nrf5_sdk_1.7.1, the BLE_APP_UART example will get stuck 0

bool erase_bonds; // Initialize. uart_init(); log_init(); timers_init(); //buttons_leds_init(&erase_bonds); // power_management_init(); ble_stack_init(); gap_params_init...
22 views

0 replies

Started 7 hours ago
by shsh
Not Answered
the file: thingy53_nrf5340_cpuapp.conf in v2.6.0/bootloader/mcuboot/boot/zephyr/boards 0

Hi Community, I made a custom board based on thingy53, created a similar custom board file folder. The application code can be compiled correctly with the original thingy53...
29 views

0 replies

Started 19 hours ago
by danny0007
Not Answered
QSPI initialization error sdk v2.6.1 0

Hello I am trying to initialize qspi in a ".cpp" file and methods like PINCTRL_DT_DEFINE ( QSPI_NODE ); are giving me "out-of-order initializers are nonstandard in C...
33 views

0 replies

Started 20 hours ago
by kalbani

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022