Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
matter light switch 0

example Matter_light_switch in vs code version using nrf connect sdk -> v2.8.0 manage tool-chain version v2.8.0 nrf52840dk getting error while building code ...
18 views

0 replies

Started 1 day ago
by Prajwal Tayade
Not Answered
DECT NR+ power class and bandwidth/data rate 0

Hello, I have a few questions about the nRF9151 DECT NR+ modem. I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
18 views

0 replies

Started 1 day ago
by Mark Szente
Not Answered
how to obtain a fixed BLE MAC address when CONFIG_BT_PRIVACY is defined 0

Hi, I am using nrf52840 to develop a product. I use NCS sdk v2.5.0. I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
26 views

0 replies

Started 1 day ago
by zhuweihua163
Not Answered
Setting CONFIG_BT_CTLR_DATA_LENGTH_MAX=251 but payload is limited to 229 bytes. 0

We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version. We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
27 views

0 replies

Started 1 day ago
by Mike.Redd
Not Answered
Disable and enable BLE OTA/DFU service 0

Hi, Platform: nRF54L15, SDK 2.9 The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
20 views

0 replies

Started 1 day ago
by SubuMuthu

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022