Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SAADC 0

Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
458 views

0 replies

Started over 5 years ago
by shark
Not Answered
Engineer needed for OTA Project 0

I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU. nRF52810 must have command- and data mode over UART, Pic controler...
392 views

0 replies

Started over 5 years ago
by pschoon
Not Answered
Initialization and operation of sensor mpu6050 with nrf52840 development board 0

I want to be able to read the gyro and accelerometer values from the MPU6050 sensor. As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
- development
- software
- nrf52
- windows
- SDK Documentation
- beginner
- nrf52840 dk
- nRF Tools
- nRF Series products
- C
- nrf52840
- s140
- twi
811 views

0 replies

Started over 5 years ago
by MRK-196
Not Answered
how to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I should use SHA256 and MD5. I made my code as below. NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
775 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
How to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I want to use SHA256 as below. output32Byte = SHA256[input32Byte]; Which function or example can I refer to? And also I want to...
1269 views

0 replies

Started over 5 years ago
by roger.k

Recent in Nordic blog

Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014
Sniffer application for OS X

RK

I've put up on Sourceforge, a Mac OSX application which interfaces with the Nordic BTLE sniffer software and has some of the functionality of the Windows application Nordic ships with that software package…
- 1 Oct 2014
Getting started with nRF51 development on Mac OS X

Eirik Midttun

Update: Since this blog was originally written the nrfjprog tool has been ported to OS X (now macOS). This means that the flash programming is much simpler, and it is simply a matter of following the documentation…
- 1 Sep 2014

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019