Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SAADC 0

Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
560 views

0 replies

Started over 5 years ago
by shark
Not Answered
Engineer needed for OTA Project 0

I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU. nRF52810 must have command- and data mode over UART, Pic controler...
485 views

0 replies

Started over 5 years ago
by pschoon
Not Answered
Initialization and operation of sensor mpu6050 with nrf52840 development board 0

I want to be able to read the gyro and accelerometer values from the MPU6050 sensor. As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
- development
- software
- nrf52
- windows
- SDK Documentation
- beginner
- nrf52840 dk
- nRF Tools
- nRF Series products
- C
- nrf52840
- s140
- twi
957 views

0 replies

Started over 5 years ago
by MRK-196
Not Answered
how to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I should use SHA256 and MD5. I made my code as below. NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
935 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
How to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I want to use SHA256 as below. output32Byte = SHA256[input32Byte]; Which function or example can I refer to? And also I want to...
1439 views

0 replies

Started over 5 years ago
by roger.k

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017