Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
how to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I should use SHA256 and MD5. I made my code as below. NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
937 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
How to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I want to use SHA256 as below. output32Byte = SHA256[input32Byte]; Which function or example can I refer to? And also I want to...
1441 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
Does the nRF52840DK[PCA10056] support IPSP service serialization (e.g. sd_ble_l2cap_ch_setup) connected with pc-ble-driver? 0

I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
- development
- software
- nrf52840 dk
- softdevice
- bluetooth le
- nrf52840
- s140
777 views

0 replies

Started over 5 years ago
by RyanChu
Not Answered
how to get the data from two uarts in nRF52840 0

hi... i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
765 views

0 replies

Started over 5 years ago
by ps_anu
Not Answered
BLE consumption peripheral to high 0

Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral After the connection I need to save power at the peripheral board, because the cpnsumptio...
777 views

1 reply

Latest over 5 years ago
by Stian Røed Hafskjold

Recent in Nordic blog

Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018