Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF Connect VScode project issue with GPIO configuration 0

Hi, I created a simple project in VS Code and I have defined the custom board configuration files that I want. In the xxx_defconfig file I have defined CONFIG_GPIO=y but...
22 views

0 replies

Started 12 hours ago
by masterLee
Not Answered
CONFIG_NRFX_TIMER1 was assigned the value y, but got the value n. Missing dependencies: HAS_NRFX || (HAS_NRFX && 0) || ((UART_0_NRF_HW_ASYNC_TIMER = 1 || UART_1_NRF_HW_ASYNC_TIMER = 1 || UART_2_NRF_HW_ASYNC_TIMER = 1 || UART_3_NRF_HW_ASYNC_TIME 0

Im using nrf5340 with nrf connect SDK 2.6. Im trying to follow this post to evaluate hardware timer for reading saadc But I constantly am getting CONFIG_NRFX_TIMER1...
19 views

0 replies

Started 12 hours ago
by IvanR
Not Answered
Adding MCUBOOT and QSPI device to DTS causes no boot 0

I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1. I'm able to build the SMP server sample...
30 views

0 replies

Started 15 hours ago
by frankenboom
Not Answered
ncs 2.8.0 fails to build zephyr's bluetooth ISO_CENTRAL and ISO_PERIPHERAL samples on 52840DK 0

HW: 52840DK PCA10056 3.0.1 2023.16 NCS SDK: v2.8.0 I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
44 views

0 replies

Started 18 hours ago
by banco
Not Answered
When connecting to AWS IoT with low signal it gets stuck 0

We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
33 views

0 replies

Started 22 hours ago
by charleshaf

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020
Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020