Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Can I get current transmitting channel in nRF52832 0

Hi, I'm wondering if I can get current transmitting channel during a connection. So Is there a way I can directly read current transmitting channel? If not, is...
- channel
- 10040 nrf52832 s132
1288 views

0 replies

Started over 8 years ago
by saintnever
Not Answered

How exactly the "recursive" calls to "app_sched_execute" are fixed in SDK14 Bootloader ? 0

This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below: devzone.nordicsemi...

890 views

0 replies

Started over 8 years ago
by sdaexpert
Not Answered

advertisement with whitelisting 0

hi. How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...

1049 views

0 replies

Started over 8 years ago
by anuja
Not Answered

througput parameter 0

why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)? Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...

843 views

0 replies

Started over 8 years ago
by Stayhungry
Not Answered

why Error: L6218E: Undefined symbol app_sched_init (referred from main.o). 0

Hi, I am using Keil IDE to develop nRF51822 project. in main(), the command line APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE); has Error : L6218E...

1745 views

0 replies

Started over 8 years ago
by DYNAMICTOYS

Recent in the DevZone Blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

scytulip

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014