Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Writing to flash memory 0

Hi, I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex. I want to write some information (just 4 bytes) to flash memory,...
- development
- software
- flash
- nrf52810
15 views

0 replies

Started 6 hours ago
by Kenneth_CBS
Not Answered
Unable to configure nRF Sniffer for 802.15.4 for ZigBee 0

Hello All, I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup, https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
13 views

0 replies

Started 6 hours ago
by UVP
Not Answered
Can't open syscall/gpio.h 0

Hi everyone, I am getting this build error while I am trying to call a function from gpio.h in my custom code Looking at my includes I see this This is a really...
15 views

0 replies

Started 6 hours ago
by ReginaA101
Not Answered
Timeout exit from the boot loader 0

I am developing an application that uses NCS2.8.0. For FW updates, the nRF52833 USB ACM bootloader is enabled. However, there are some problem. My device has a battery...
15 views

0 replies

Started 7 hours ago
by DX_HK
Not Answered
nrf52840-read data 0

Hello forum , In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
21 views

0 replies

Started 7 hours ago
by pushparaj

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software: nRF Desktop on a Development Kit

Priyanka

This tutorial is aimed at implementing the nRF Desktop application on the nRF52840 Development Kit (DK) using the nRF Connect SDK, thereby allowing it to work either as a gaming mouse, keyboard, or dongle…
- 16 Dec 2021
Software: Add DFU support to your application

Simon

This guide is for an older version of the nRF Connect SDK. For a newer guide on Bootloaders and DFU, we recommend https://academy.nordicsemi.com/courses/nrf-connect-sdk…
- 29 Nov 2021
Software: Common fixes for nRF Connect SDK build problems

Sigurd Hellesvik

Does your build fail today, even though it worked fine yesterday? Are you able to build your project on another computer, but not the one you need to use now? Here are eight things you can try to fix these…
- 22 Sep 2021
Peripherals And RF Test: TWI/I2C implementation with nRFx TWIS Driver

Jeff4BLE

Objectives Learn to add and configure an I2C/TWI Master Zephyr driver to an NRF Connect SDK project. Learn to add and configure an I2C/TWI Slave nRFX driver to an NRF Connect SDK project. Demonstrate…
- 4 Aug 2021
Peripherals And RF Test: Using the nRF Connect SDK / West to program the Radio_Test example into the nRF5340 DK for agency testing.

Jay Tyzzer

Using the nRF Connect SDK / West to Program the Radio_Test example into the nRF5340 DK Background: There is a need to be able to put a Nordic Semiconductors System-on-Chip / transceiver into modes where…
- 3 Aug 2021
Software: Updating to the MPSL Timeslot interface

Daniel Veilleux

The "Concurrent Multiprotocol Timeslot API" was introduced with v7.0 of the S110 SoftDevice in 2014. The original purpose was to allow customers to build their own proprietary networks using…
- 2 Aug 2021