Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Tx power configuration in SDK 2.7.0 0

Hi, I'm a little disoriented. I used to set the tx power configuration for the nRF5340: in the file <prjdir>\child_image\hci_rpmsg.conf. How and where can I set the...
20 views

0 replies

Started 13 hours ago
by PabloL
Not Answered
nrfCloud Rest API provisioning is not working 0

Hello I have a custom board based on nrf9160 and I cannot claim and make REST API and JWT auth work for it. These are the steps I followed 1. https://github.com/nRFCloud...
27 views

0 replies

Started 18 hours ago
by alespit
Not Answered
Bluetooth address and settings_load() 0

Hello all, i have a problem and I hope that someone can help me. I can change the bluetooth address of the device with the following code: and this is okay. I have...
25 views

0 replies

Started 19 hours ago
by Epasta
Not Answered
Impedance Control nrf9151 RF Design 0

Hello, It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue: Here is the...
26 views

0 replies

Started 19 hours ago
by Doug K
Not Answered
nRF52840 (aQFN73) vias to bottom layer 0

Hi We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
42 views

0 replies

Started 21 hours ago
by Michael-42

Recent in Nordic blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019