Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Setting CONFIG_BT_CTLR_DATA_LENGTH_MAX=251 but payload is limited to 229 bytes. 0

We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version. We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
32 views

0 replies

Started 1 day ago
by Mike.Redd
Not Answered
Disable and enable BLE OTA/DFU service 0

Hi, Platform: nRF54L15, SDK 2.9 The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
23 views

0 replies

Started 2 days ago
by SubuMuthu
Not Answered
Ring Buffer Maximum Size 0

Hello, I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
24 views

0 replies

Started 2 days ago
by connorshannon
Not Answered
Flash nRF52840 dongle with Sweyntooth firmware 0

Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
23 views

0 replies

Started 2 days ago
by DavidXie
Not Answered
Warning FLASH_SIMULATOR unassigned starting from NCS SDK 2.7.0 due to missing default flash_sim.overlay from build 0

I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
25 views

0 replies

Started 2 days ago
by Alfredo Antolinez

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019