Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Wouldn't update connection params 0

Hi, I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init: static void conn_params_init(void){ uint32_t err_code; ble_conn_params_init_t...

723 views

0 replies

Started over 7 years ago
by Alice
Not Answered
how to use whitelist in ble_app_hrs_c 0

S130, SDK 12.3, ble_app_hrs_c example. I want to use whitelist function in this example but I can't finish it. When I run peer_list_get(), it gets all 0xFF, means that...
- s130
- whitelist
- ble_app_hrs_c
- nrf51822
885 views

0 replies

Started over 7 years ago
by kamisen
Not Answered

services size is zero 0

sometime,i use android app to scan ble device,it will display "the device dose not has required services",the gatt.getServices.size is zero.why?

547 views

0 replies

Started over 7 years ago
by nowen
Not Answered
one wire library for nrf51822 keil 0

one wire library for nrf51822 keil for connected ds18b20 .
- nrf51822 keil one wire
760 views

0 replies

Started over 7 years ago
by morteza1994
Not Answered
Nordic NFR52832 Two Masters with FTDI SPI-USB Bridge 0

Hi all, I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
- c232hm
- adc
- qt
- nfr52832
- ftdi bridge
- spi
- keil
- spi-usb
985 views

0 replies

Started over 7 years ago
by bryanhsieh

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019