Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Ble connection details not showing up in wireshark 0

Hello, I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...

875 views

0 replies

Started over 9 years ago
by Newbie
Not Answered

[bug report & fix] app_uart_fifo is sending APP_UART_TX_EMPTY event before the last byte is sent 0

Hi Team, We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...

2027 views

0 replies

Started over 9 years ago
by Patrice Rudaz
Not Answered
Pairing procedure failed by bonding 0

Hello everybody, for my project, i will bond the peripherial with the central. I test my device with the MCP and can connect without problems. When i press the Bond Button...
- bond
- sdk11
- s132
- nrf52832
1416 views

0 replies

Started over 9 years ago
by 1_andi
Not Answered
nRF52 max. input frequency on GPIO 0

Hi all, I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
- 132 nrf52832 gpio
2293 views

0 replies

Started over 9 years ago
by Pascal Künzi
Not Answered
NRF52840DK w/S140 hardfault 0

Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio. App flash base is set to 0x00021000 and app RAM base is set to 0x20003000 Looking at the CPU...
- nrf52840dk nrf52 nrfgo
783 views

0 replies

Started over 9 years ago
by Ove-Anders Gaarder Aune

Recent in the DevZone Blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015