Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

One RX and Three TX system with NRF24L01+ 0

This system does not work if I enable the third Pipe (Pipe2) . The system is working without any problem as one RX and two TX (Pipe0 and Pipe1). The problem on enabling...

518 views

0 replies

Started over 7 years ago
by Erol
Not Answered
sd_flash_write inside BLE event 0

Hello, i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method. What i would like to do is to write to flash from...
- sd_flash_write
- event
- ble
- flash
- nrf52832
979 views

0 replies

Started over 7 years ago
by schef
Not Answered
sd_flash_write in BLE event 0

Hello, i have read all posts about writing to FLASH when using BLE. But could not find the desirable method. What i would like to do is to write to flash from characteristic...
- sd_flash_write
- event
- nrf52
- ble
- flash
980 views

0 replies

Started over 7 years ago
by schef
Not Answered

Product Key telling me can't add product to my list 0

I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide Thank you

662 views

0 replies

Started over 7 years ago
by Dino
Not Answered
problem communicating with NRF24L01+? How to choose pipeline address? 0

hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
- nrf24l01 protocol
- arduino
616 views

0 replies

Started over 7 years ago
by DAVY

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019