Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

One RX and Three TX system with NRF24L01+ 0

This system does not work if I enable the third Pipe (Pipe2) . The system is working without any problem as one RX and two TX (Pipe0 and Pipe1). The problem on enabling...

507 views

0 replies

Started over 7 years ago
by Erol
Not Answered
sd_flash_write inside BLE event 0

Hello, i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method. What i would like to do is to write to flash from...
- sd_flash_write
- event
- ble
- flash
- nrf52832
969 views

0 replies

Started over 7 years ago
by schef
Not Answered
sd_flash_write in BLE event 0

Hello, i have read all posts about writing to FLASH when using BLE. But could not find the desirable method. What i would like to do is to write to flash from characteristic...
- sd_flash_write
- event
- nrf52
- ble
- flash
967 views

0 replies

Started over 7 years ago
by schef
Not Answered

Product Key telling me can't add product to my list 0

I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide Thank you

653 views

0 replies

Started over 7 years ago
by Dino
Not Answered
problem communicating with NRF24L01+? How to choose pipeline address? 0

hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
- nrf24l01 protocol
- arduino
607 views

0 replies

Started over 7 years ago
by DAVY

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

Dinesh Harjani

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

notsane0

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

bjorn-spockeli

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019